Table of Contents

Thermo King
Frigoblock
Help
- FAQ
- TK TV
- Contact Us
Search Term

English French Spanish italiano Deutsche Portuguese русский — Russian Japansese 中文 — Chinese

Contact : tk_emea_infocentral_support@thermoking.com

View as Table of Contents View as One Page

Precedent Single Temperature Units

- i Preface For None
- ii Introduction
  - Software License
  - Assistance/Feedback
Chapter 1: Safety Precautions
- 1.1: Danger, Warning, Caution, and Notice
- 1.2: General Safety Practices
- 1.3: Automatic Start/Stop Operation
- 1.4: Electrical Hazard
- 1.5: Battery Installation and Cable Routing
- 1.6: Refrigerant
- 1.7: Refrigerant Oil
- 1.8: First Aid
- 1.9: Safety Decals and Locations
Chapter 2: Unit Description
- 2.1: Unit Overview
- 2.2: Diesel Engine
- 2.3: Extended Life Coolant (ELC)
- 2.4: EMI 3000
- 2.5: Thermo King X430 Series Reciprocating Compressor
- 2.6: Electronic Throttling Valve
- 2.7: SMART REEFER 4 (SR-4) Control System
- 2.8: CYCLE-SENTRY™ Start-Stop Controls
- 2.9: Data Logging
- 2.10: OptiSet Plus™
- 2.11: FreshSet™
- 2.12: Defrost
- 2.13: Opening the Front Doors
- 2.14: Engine Compartment Components
- 2.15: Unit Protection Devices
Chapter 3: Manual Pretrip Inspection and Loading Procedures
Chapter 4: Operating Instructions
- 4.1: SMART REEFER 4 (SR-4) Control System
  - 4.1.1: Microprocessor On/Off Switch
  - 4.1.2: SR-4 HMI Control Panel
- 4.2: Turning Unit On
  - 4.2.1: If a Flash Drive is Connected
  - 4.2.2: Configurable Soft Keys
  - 4.2.3: Display Heater
  - 4.2.4: If a Language is Enabled
  - 4.2.5: If Log Alarms are Present
- 4.3: Turning The Unit Off
- 4.4: The Standard Display
- 4.5: The TemperatureWatch™ Display
- 4.6: Changing The Setpoint
  - 4.6.1: Numerical Setpoints
  - 4.6.2: Named Products - OptiSet Plus
  - 4.6.3: Both Numerical Setpoints and Named Products
  - 4.6.4: Changing the Setpoint - Numerical Setpoint
  - 4.6.5: Changing the Setpoint - Named Product
  - 4.6.6: Changing the Setpoint - Both Numerical Setpoint and Named Product Available
- 4.7: Starting the Diesel Engine
- 4.8: Starting the Electric Motor
- 4.9: Switching from Diesel to Electric
- 4.10: Switching from Electric to Diesel
- 4.11: Initiating a Manual Defrost Cycle
  - 4.11.1: Terminating a Defrost Cycle
- 4.12: Selecting Cycle Sentry or Continuous Mode
- 4.13: Using the Gauges Key
  - Gauges Available
- 4.14: Using the Sensors Key
  - Sensors Available
- 4.15: Using the Main Menu
  - Main Menu Choices
  - 4.15.1: Pretrip
  - 4.15.2: Performing a Pretrip Test
  - 4.15.3: Flash Drive
  - 4.15.4: Languages
  - 4.15.5: Alarms
  - 4.15.6: Gauges
    - Displaying Gauges
  - 4.15.7: Sensors
    - Displaying Sensors
  - 4.15.8: Data Logger (CargoWatch)
    - Sending Start of Trip Marker to CargoWatch and ServiceWatch Data Loggers
    - Printing CargoWatch Data Logger Reports
  - 4.15.9: Hourmeters
    - Viewing Hourmeters
    - Hourmeter Names and Definitions
  - 4.15.10: Mode
  - 4.15.11: SmartPower™ Electric Standby Option
  - 4.15.12: Adjust Brightness
  - 4.15.13: Time
  - 4.15.14: Clear All ECU Faults
Chapter 5: Alarm Codes
- Introduction
- 5.1: Alarm Types
- 5.2: Clearing Alarm Codes
Chapter 6: Loading and Inspection Procedures
- 6.1: Pre-Loading Inspection
- 6.2: Post-Loading Inspection
- 6.3: Enroute Inspections
Chapter 7: Jump Starting
Chapter 8: Specifications
Chapter 9: Maintenance Inspection Schedule
Chapter 10: Serial Number Locations
Chapter 11: Emergency Cold Line
Chapter 12: Warranty
- 12.1: EPA and ARB Supplemental Emissions Warranty Statement
Chapter 13: CALIFORNIA Proposition 65 Warning

<Previous

Next>

Safety Precautions

In this section:

Danger, Warning, Caution, and Notice
General Safety Practices
Automatic Start/Stop Operation
Electrical Hazard
Battery Installation and Cable Routing
Refrigerant
Refrigerant Oil
First Aid
Safety Decals and Locations

<Previous

Next>

Building One-Page View

This might take a few seconds.