Detailed Specifications
Diving Wall ATP Specification
Diving wall ATP Specification
| K factor coefficient | Minimum thickness of diving wall | ||
| Removable | Fixed | ||
| GRP floor Longitudinal |
2.0 W/m2.K |
1.5 W/m2.K |
25 mm |
| GRP floor Transversal |
2.6 W/m2.K |
1.5 W/m2.K |
40 mm |
| Aluminium floor Longitudinal |
3.0 W/m2.K |
2.0 W/m2.K |
25 mm |
| Aluminium floor Transversal |
3.2 W/m2.K |
2.0 W/m2.K |
40 mm |
Diving wall coefficients include a safety margin to allow for degradation and thermal leakages.
Refrigerated Unit capacity:
| Refrigeration capacities 1 | |||
| Refrigerant | R-404A/R-452A | ||
| Unit Model | T-1200R Spectrum S3+S3 | ||
| Total Nominal | Remote Evaporator S3 | ||
| Capacity on engine power | 0 °C | 12 080 W | 8 120 W |
| -20 °C | 7 620 W | 4 640 W | |
| Capacity on electric standby | 0 °C | 7 560 W | 7 163 W |
| -20 °C | 4 720 W | 4 010 W | |
| Unit Model | T-1000R Spectrum S3+S3 | ||
| Total Nominal | Remote Evaporator S3 | ||
| Capacity on engine power | 0 °C | 9 990 W | 7 540 W |
| -20 °C | 5 790 W | 4 230 W | |
| Capacity on electric standby | 0 °C | 6 280 W | 6 190 W |
| -20 °C | 3 860 W | 3 490 W | |
| Unit Model | T-1200R Spectrum S3+S3 | ||
| Total Nominal | Remote Evaporator S3 | ||
| Capacity on engine power | 0 °C | 10 560 W | 7 720 W |
| -20 °C | 6 030 W | 4 410 W | |
| Capacity on electric standby | 0 °C | 7 560 W | 6 840 W |
| -20 °C | 4 720 W | 3 820 W | |
| Airflow volume at 0 Pa static pressure |
2 000 m3/hr |
||
| Discharge velocity (Air throw) | 9.50 m/sec | ||
| Refrigerant | R-452A | ||
| Unit Model | UT-R Spectrum S3+S3 | ||
| Total Nominal | Remote Evaporator S3 | ||
| Capacity on engine power | 0 °C | 11 302 W | 7 780W |
| -20 °C | 6 374 W | 4 463 W | |
|
Capacity on electric standby |
0 °C | 10 249W | 6 861 W |
| -20 °C | 4 497 W | 3 652 W | |
| Airflow volume at 0 Pa static pressure |
2 350 m3/hr |
||
|
Discharge velocity (Air throw) |
9.50 m/sec |
||
| Maximum zone length (2) | 5.50 m | ||
|
1 At +30°C ambient temperature under ATP conditions |
|||
|
2 Maximum recommended dimensions: these are guidelines based on airflow and air velocity requirements based upon the following assumptions: K factor = 0.4W/m2.K, internal height up to 2.5 m, width up to 2.5 m, zero heat load from produce carried. For each application, a heat load calculation must be performed (applies to all listed unit models). |
|||