T-590/690/890/1090 Series and UT-1290

• • i Preface For None
  • ii Introduction
    • Software License
    • Assistance/Feedback
• Chapter 1: Safety Precautions
  • 1.1: Danger, Warning, Caution, and Notice
  • 1.2: General Practices
  • 1.3: Automatic Start/Stop Operation
  • 1.4: Electrical Hazard
    • Low Voltage
  • 1.5: Refrigeration System Hazards
  • 1.6: Refrigerant Oil Hazards
  • 1.7: Welding Precautions
  • 1.8: Safety Nameplates
  • 1.9: First Aid
• Chapter 2: Unit Description
  • 2.1: General Description
  • 2.2: Design Features
  • 2.3: Unit Options
  • 2.4: Engine
  • 2.5: ELC (Extended Life Coolant)
  • 2.6: Clutch
  • 2.7: Reciprocating Compressor
  • 2.8: HMI Controller
  • 2.9: CYCLE-SENTRY™ Start/Stop System
  • 2.10: Defrost
  • 2.11: TracKing™
  • 2.12: SmartPower Electric Standby (Model 50 Units Only)
    • Standard Features
    • SmartPower Optional Features
  • 2.13: Unit Protection Devices
  • 2.14: Engine Compartment Components
  • 2.15: Unit Components
• Chapter 3: Operating Instructions for Premium HMI Control Panel
  • 3.1: Truck Premium Display HMI Control Panel
    • Features
    • Display
    • Hard Keys
    • Soft Keys
    • 3.1.1: Turning the Unit On and Off
      • If More Than One Language is Enabled
    • 3.1.2: The Standard Display
    • 3.1.3: Changing the Setpoint
    • 3.1.4: Starting the Diesel Engine
    • 3.1.5: Starting the Electric Motor
    • 3.1.6: Switching from Diesel to Electric
    • 3.1.7: Switching from Electric to Diesel
    • 3.1.8: Initiating a Manual Defrost Cycle
      • Terminating a Defrost Cycle
    • 3.1.9: Selecting High Speed Lockout Mode (If Enabled)
    • 3.1.10: Using the Gauges Key
      • Gauges Available
    • 3.1.11: Using the Sensors Key
      • Sensors Available
    • 3.1.12: Using The Main Menu
      • Main Menu Choices
    • 3.1.13: Languages
    • 3.1.14: Alarms
      • Log Alarms
      • Check Alarms
      • Shutdown Alarms
      • Prevent Alarms
      • Pretrip Alarm Codes
      • Alarm Codes When Switching Between Diesel and Electric
      • Alarm Code Notification
      • Clearing Alarm Codes
      • Displaying and Clearing Alarm Codes
    • 3.1.15: Table of Alarm Codes
    • 3.1.16: Datalogger
    • 3.1.17: Hourmeters
      • Hourmeter Names and Definitions
    • 3.1.18: Mode
    • 3.1.19: Selecting CYCLE-SENTRY or Continuous Mode
    • 3.1.20: Selecting Temperature Display Units
    • 3.1.21: Keypad Lockout
    • 3.1.22: Selecting Sleep Mode
    • 3.1.23: Pretrip
      • Pretrip Test Conditions
      • Conditions where Pretrip Tests are Not Allowed
      • Pretrip Test Sequence
      • Pretrip Test Considerations
      • Performing a Pretrip Test
    • 3.1.24: Diesel/Electric Menu
    • 3.1.25: Adjust Brightness
    • 3.1.26: Time
• Chapter 4: Loading and Enroute Inspections
• Chapter 5: Specifications
  • Engine Specifications
  • Refrigeration System
  • Electrical Control System Specifications
  • Fuses
  • Electric Standby Specifications (SmartPower™ Model 50 Units)
  • Electric Motor and Overload Relay
  • Standby Power Requirements
• Chapter 6: Unit Maintenance
  • 6.1: Maintenance Inspection Schedule
• Chapter 7: Serial Number Locations
• Chapter 8: Emergency Cold Line
• Chapter 9: Unit Warranty
  • 9.1: EPA and ARB Supplemental Emissions Warranty Statement