Truck Premium Display HMI Control Panel

The Truck Premium Display is used to operate the unit, display unit information, and access all Maintenance and Guarded Access Menus. The Truck Premium Display communicates with the Base Controller via the Controller Area Network (CAN) bus. It is connected to the Base Controller via CAN Connector J14 on the interface board. The Truck Premium Display is typically located in the vehicle driver’s compartment. It may be installed in the truck instrument panel using a DIN mounting ring or under the instrument panel using an under dash mounting kit.

Truck Premium HMI Control Panel

The HMI control panel consists of a display and 8 touch-sensitive keys.

The display is capable of showing both text and graphics.

The keys on the left and right sides of the display are dedicated single function “hard” keys.

The four keys under the display are “soft” keys. The functions of these soft keys change depending on the operation being performed. If a soft key is active the current key function is shown in the display directly above the key.

In this section:

  1. Turning the Unit On and Off
  2. The Standard Display
  3. Changing the Setpoint
  4. Starting the Diesel Engine
  5. Starting the Electric Motor
  6. Switching from Diesel to Electric
  7. Switching from Electric to Diesel
  8. Initiating a Manual Defrost Cycle
  9. Selecting High Speed Lockout Mode (If Enabled)
  10. Using the Gauges Key
  11. Using the Sensors Key
  12. Using The Main Menu
  13. Languages
  14. Alarms
  15. Table of Alarm Codes
  16. Datalogger
  17. Hourmeters
  18. Mode
  19. Selecting CYCLE-SENTRY or Continuous Mode
  20. Selecting Temperature Display Units
  21. Keypad Lockout
  22. Selecting Sleep Mode
  23. Pretrip
  24. Diesel/Electric Menu
  25. Adjust Brightness
  26. Time
Parent topic: Operating Instructions for Premium HMI Control Panel

Features

  • Displays Box Temperature and Setpoint in Fahrenheit or Celsius

  • Displays Engine Running and Motor Running Hourmeters

  • Changes Setpoint

  • Indicates Alarm Condition Exists

  • Displays and Clears Alarms

  • Selects and Indicates CYCLE-SENTRY or Continuous Mode Operation

  • Selects and Indicates High Speed Lock-Out Operation

  • Initiates and Indicates a Defrost Cycle

  • Initiates and Indicates a Pretrip Test

  • Sends a Start of Trip to the ServiceWatch data logger.

Display

The display presents information to the operator. This information includes setpoint and temperature, unit operating information, gauge readings, temperatures, and other information as selected by the operator.

Display

The Standard Display of box temperature and setpoint is shown ( Display). The CYCLE-SENTRY Icon in the upper right of the display shows the unit is running in CYCLE-SENTRY (Start-Stop) Mode. The unit has a setpoint of 35°F, and an actual box temperature of 35.8°F. The down-pointing arrow at the left side of the display shows the unit is cooling.

The four keys under the display are termed "soft" keys. The functions of these keys change depending on the operation being performed. The function of each soft key is shown by labels in the display located directly above each soft key. In the example shown ( Display), pressing the left soft key accesses the SETPOINT Menu and pressing the right soft key accesses the MAIN Menu. The other two soft keys access the GAUGES menu and SENSORS menu as shown by the labels above the keys.

Hard Keys

Hard Keys

The keys on either side of the display are dedicated or "hard" keys. Their function always remains the same.

This key is used to turn the unit on. First the display will briefly show the Thermo King Logo and then the statement "Configuring System - Please Wait". When the power-up sequence is complete the display shows the Standard Display of box temperature and setpoint. For more information see "Turning the Unit On and Off" later in this section.

This key is used to turn the unit off. First the display will briefly show "System is Powering Down - Please Wait. Press On to Resume" and then "Off" will appear momentarily. When the power-down sequence is complete the display will be blank. For more information see "Turning the Unit On and Off" later in this section.

This key is used to initiate a manual defrost cycle. For more information see "Initiating a Manual Defrost Cycle" later in this section.

This key is used to lock out high speed operation in noise sensitive areas. For more information see "Selecting High Speed Lockout" later in this section.
Note The Thermo King Premium Truck HMI Control Panel features a High Speed Lock-Out key as shown here. The Thermo King Truck HMI Control Panel features a Cycle Sentry key in this position. When using the Thermo King Premium Truck HMI Control Panel, Cycle Sentry Mode or Continuous Mode is selected from the Main Menu – Mode Submenu as shown later in this section.

Soft Keys

Soft Keys

 The four "soft" keys under the display are multi-purpose keys. Their function changes depending on the operation being performed. If a soft key is active the key function is shown in the display directly above the key. The keys are numbered from left to right, with Key 1 on the far left and Key 4 on the far right.

Typical soft key functions:

MENU + or - HOURMETERS EXIT
NEXT SELECT GAUGES HELP
YES/NO CLEAR BACK SENSORS