Electrical System
B-100
| Fuses | |||
| 12 Vdc | 24 Vdc | ||
| Fuse 1: Main Fuse | 100 amps | 60 amps | |
| Fuse 3: Evaporator Fan Motor (EFM1) | 15 amps | 10 amps | |
| Fuse 5: Roadside (Engine) Compressor Clutch (CCL1), Liquid Injection Switch (LIS), Liquid Injection Valve (LIV), EVAP1 Defrost Hot Gas Solenoid Valve (PS1), Compressor Motor Contactor (CMC), Heat Pilot Solenoid (PS5) | 20 amps | 10 amps | |
| Fuse 6: Drain Heaters (H3 and H4) | 2 amps | 2 amps | |
| Fuse 7: Transformer AC Power Supply 2 | 10 amps | 10 amps | |
| Fuse 8: Heater | 72 °C (161.5 °F) | 72 °C (161.5 °F) | |
| Fuse 9: Heater | 72 °C (161.5 °F) | 72 °C (161.5 °F) | |
| Fuse 10: Heater | 72 °C (161.5 °F) | 72 °C (161.5 °F) | |
| Fuse 11: Heater | 72 °C (161.5 °F) | 72 °C (161.5 °F) | |
| Fuse 14: Vehicle Ignition Switch | 5 amps | 5 amps | |
| Fuse 20: Transformer AC Power Supply (located at compressor motor contactor in condenser section) | 4 amps | 4 amps | |
| Fuse 16: Thermal Fuse | 10 A 84ºC | 10 A 84ºC | |
| Fuse 17: Thermal Fuse | 10 A 84ºC | 10 A 84ºC | |
| Fuse 25: Battery Fuse | 5 amps | 5 amps | |
| Fuse 30: Condenser Fan Motor (CFM) (located in CF1 wire near terminal strip in condenser section) | 16 amps | 10 amps | |
| Fuse 31: Fuse - Heater 1 | 20 amps | 20 amps | |
| Fuse 32: Fuse - Heater 2 | 20 amps | 20 amps | |
| Fuse 33: Fuse - Heater 3 | 20 amps | 20 amps | |
| Fuse 34: Fuse - Heater 4 | 20 amps | 20 amps | |
| Condenser Fan Motor | |||
| Voltage | 13 Vdc | 26 Vdc | |
| Full Load Current | 10 Amps | 4.7 Amps | |
| Power Rating | 130 W | 122 W | |
| RPM with Full Load | 2,800 | 2,800 | |
| Evaporator Fan Motors (Each) | |||
| Voltage | 13 Vdc | 26 Vdc | |
| Full Load Current | 7.5 Amps | 4 Amps | |
| Power Rating | 97.5 W | 104 W | |
| RPM with Full Load | 2,800 | 2,800 | |
| AC Electrical Power Supply Motor | |||
| Voltage/Phase/Frequency | 230/1/50 | ||
| Output Power | 0.75 kW | ||
| Nominal Current Drawn | 5.2 amps | ||
| OL Relay Adjustment |
10 / 20 Units - 5.2 Amps 30 / 50 Units - 10.5 Amps |
||
| DC Electrical Power Supply Motor | |||
| Voltage | 12 Vdc | 24 Vdc | |
| Output Power | 600 W | 600 W | |
| Nominal Current Drawn | 65 amps | 30 amps | |
| Coil for Hot Gas Solenoid (PS1) | |||
| Voltage | 12 Vdc | 24 Vdc | |
| Current | 2.3 amps | 1.3 | |
| Resistance | 5.2 ohms | 20 ohms | |
| Coil for Liquid Injection Solenoid (LIS) – MAX Only | |||
| Voltage | 12 Vdc | ||
| Current | 1.2 amps | ||
| Resistance | 10.0 ohms | ||
| Coil for Heat Pilot Solenoid (PS5) - Truck Engine Coolant Heat Option Only | |||
| Voltage | 12 Vdc | ||
| Current | 1.5 amps | ||
| Resistance | 8.0 ohms | ||
| Drain Line Heaters (Each) - MAX Only | |||
| Voltage | 12 Vdc | ||
| Current | 0.9 amps ± 5% at 68 F (20 C) | ||
| Resistance | 13.8 ohms ± 5% at 68 F (20 C) | ||
| Battery Relay (BATR) | |||
| Type | Single Pole Single Throw (SPST) | ||
| Contacts | Terminals 30 to 87 | Normally Open (NO) | |
| Coil Resistance | Terminals 85 to 86 | 90 ohms | |
| Electric Standby Power Relay (STDR) | |||
| Type | Single Pole Single Throw (SPST) | ||
| Contacts | Terminals 30 to 87 | Normally Open (NO) | |
| Coil Resistance | Terminals 85 to 86 | 90 ohms | |
| Start Key Relay (C1R) | |||
| Type | Single Pole Double Throw (SPDT) | ||
| Contacts |
Terminals 30 to 87 Terminals 30 to 87A |
Normally Open (NO) Normally Closwe (NC) |
|
| Coil Resistance | Terminals 85 to 86 | 90 ohms | |
| Capacitors | |||
| Starting Capacitor (CS) – all voltages | 250–300 μF | ||
| Running Capacitor (CR) | 40 μF | ||
| Start Relay | |||
| 230/1/50 |
Start Relay – 1E39543H01 Type: Current Pick-up - 9.1 Amps Drop-out: 7.5 Amps |
||
| 230/1/60 |
Start Relay – 1E55777G01 Type: Voltage Release Range: 95-254 VAC |
||
| 115/1/60 |
Start Relay – 1E55777G01 Type: Voltage Release Range: 95-254 VAC |
||
| Compressor Motor Contactor (CMC) | |||
| Contacts | Normally Open | ||
| Coil Voltage | 12 Vdc | ||
| Coil Current | 0.25 amps | ||
| Coil Resistance | 48 ohms | ||
| Transformer | |||
| Power | 500 VA | ||
| Frequency | 50/60 Hz | ||
| Primary Inputs | 115-208-230 Vac | ||
| Secondary Nominal Voltage | 11.7 Vac (21.4 Amps) | ||
| AC / DC Power Supply Converter - 330 W | |||
| Power | 320W | ||
| Frequency | 50/60 Hz | ||
| Input |
Voltage Range: 85~264 VAC / 120~370 VDC Frequency Range: 47~63 Hz |
||
| Secondary Nominal Voltage and Specs | 12V | 24V | |
| Rated Current | 27 amps | 14 amps | |
| Current Range | 0~27 amps | 0~14 amps | |
| Rated Power | 324W | 336W | |
| Ripple and Noise (max) | 120mVp-p | 150mVp-p | |
| Voltage Adj. Range | 10.2~13.8V | 21.6~28.8V | |
| Voltage Tolerance | 1.0% | 1.0% | |
| Line Regulator | 0.3% | 0.2% | |
| Load Regulation | 0.5% | 0.5% | |
| Input | 27 amps | 14 amps | |
| 12 Vdc | |||
| Fuses | |||
| E-200 | |||
| Fuse 1: Main Fuse | 150 amps | ||
| Fuse 3: Evaporator Fan | 15 amps | ||
| Fuse 4: Evaporator second Fan | 15 amps | ||
| Fuse 5: Distribution fuse | 20 amps | ||
| Fuse 6: Drain Heaters | 2 amps | ||
| Fuse 9: Evaporator Fan second compartment | 15 amps | ||
| Fuse 11: Drain Heaters second compartment | 2 amps | ||
| Fuse 14: ACC1 Ignition Fuse | 5 amps | ||
| Fuse 25: Vehicle Battery | 5 amps | ||
| Fuse 63: | TK Battery | 1 Battery | 150 amps |
| Fuse 83: | 2 Battery | 80 amps | |
| Fuse 71: SCM Fuse | 60 amps | ||
| Fuse 72: SCM Fuse | 60 amps | ||
| Fuse 8: | BMS Fuses | 10 amps | |
| Fuse 84: | |||
| Condenser Fan Motor | |||
| Voltage | 13 Vdc | ||
| Full Load Current | 10 Amps | ||
| Power Rating | 130 W | ||
| RPM with Full Load | 2,800 | ||
| Condenser Fan Motor | |||
| Voltage | 13 Vdc | ||
| Full Load Current | 11 Amps | ||
| Power Rating | 145 W | ||
| RPM with Full Load | 2,670 | ||
| Evaporator Fan Motors (Each) | |||
| Voltage | 13 Vdc | ||
| Full Load Current | 7.5 Amps | ||
| Power Rating | 97.5 W | ||
| RPM with Full Load | 2,800 | ||
| Compressor driver module | |||
| Battery Input | 11.5 to 14.5 VDC | ||
| Isolated, balanced three-phase output: | 240 VAC Maximum | ||
| 30–300 Hz (speed controlled) | |||
| Electrical output power: | 1150 W continuous, 1400 W for 30 sec | ||
| Smart Charger module | |||
| Bidirectional battery Charger / Discharger | |||
| Voltage | 13 Vdc | ||
| Maximum Charge Current | 40 A dc | ||
| Maximum Discharge Current | 40 A dc | ||
| 12 Vdc | |||
| Fuses | |||
| E-100e and E-200e Series | |||
| Fuse 1: Main Fuse for E-100e | 100 amps | ||
| Fuse 1: Main Fuse for E-200e | 150 amps | ||
| Fuse 3: Evaporator Fan | 15 amps | ||
| Fuse 4: Evaporator second Fan | 15 amps | ||
| Fuse 5: Distribution fuse | 20 amps | ||
| Fuse 6: Drain Heaters | 2 amps | ||
| Fuse 8: Solenoids | 20 amps | ||
| Fuse 9: Evaporator Fan second compartment | 15 amps | ||
| Fuse 10 (DSR 3.1) | 15 amps | ||
| Fuse 10 (Fuse Holder): DC BUS Presence | 5 amps | ||
| Fuse 11 (DSR 3.1) | 2 amps | ||
| Fuse 11 (Fuse Holder): Battery Power Presence | 5 amps | ||
| Fuse 12 | 15 amps | ||
| Fuse 13 (Fuse Holder) | 5 Amps | ||
| Fuse 14: ACC1 Ignition Fuse | 5 amps | ||
| Fuse 25: Vehicle Battery | 5 amps | ||
| Fuse 89 | 5 amps | ||
| Fuse 90 | 5 amps | ||
| Condenser Fan Motor — E-100e | |||
| Voltage | 13 Vdc | ||
| Max. Load Current | 9.2 Amps | ||
| Power Rating | 119.60 W | ||
| Max. Airflow | 1360 m3/h | ||
| Condenser Fan Motor — E-200e | |||
| Voltage | 13 Vdc | ||
| Max. Load Current | 10.8 Amps | ||
| Power Rating | 140.4 W | ||
| Max. Airflow | 1505 m3/h | ||
| Evaporator Fan Motors (Each) | |||
| Voltage | 13 Vdc | ||
| Max. Load Current | 7.9 Amps | ||
| Power Rating | 102.7 W | ||
| Max. Airflow | 1166 m3/h | ||
V-Series
| 12 Vdc | 24 Vdc | ||
| Fuses | |||
| Common Fuses | |||
| Fuse 3: Evaporator Fan Motor (EFM1) | 15 amps | 10 amps | |
| Fuse 4: Evaporator Fan Motor (EFM2) | 15 amps | 10 amps | |
| Fuse 5: Roadside (Engine) Compressor Clutch (CCL1), Liquid Injection Switch (LIS), Liquid Injection Valve (LIV), EVAP1 Defrost Hot Gas Solenoid Valve (PS1), Compressor Motor Contactor (CMC), Heat Pilot Solenoid (PS5) | 20 amps | 10 amps | |
| Fuse 14: Vehicle Ignition Switch | 5 amps | 5 amps | |
| Fuse 30: Condenser Fan Motor (CFM) (located in CF1 wire near terminal strip in condenser section) | 16 amps | 10 amps | |
| V-100/V-200s | |||
| Fuse 6: Condenser Fan 1/2 | 2 amps | 2 amps | |
| Fuse 21: Battery Power Supply (located in 2 wire near battery) | 30 amps | 30 amps | |
| V-200/V-300 and Spectrum | |||
| Fuse 6: Condenser Fan 1/2 | 2 amps | 2 amps | |
| Fuse 8: (Spectrum Only) EVAP2 Liquid Solenoid Valve (PS2), EVAP1 Liquid Solenoid Valve (PS3), EVAP2 Defrost Hot Gas Solenoid Valve (PS4), Drain Heaters 3 and 4 (HT3, HT4) | 20 amps | 10 amps | |
| Fuse 9: (Spectrum Only) Evaporator Fan 3 | 15 amps | 10 amps | |
| Fuse 10: (Spectrum Only) Evaporator Fan 4 | 15 amps | 10 amps | |
| Fuse 11: Drain Heaters (H1 and H2) | 2 amps | 2 amps | |
| Fuse 20: Transformer AC Power Supply (located at compressor motor contactor in condenser section) | 4 amps | 4 amps | |
| Fuse 21: Battery Power Supply (located in 2 wire near battery) | 40 amps | 40 amps | |
| V-500/V-600 and Spectrum | |||
| Fuse 6: Condenser Fan 1/2 | 10 amps | 7.5 amps | |
| Fuse 8: (Spectrum Only) EVAP2 Liquid Solenoid Valve (PS2), EVAP1 Liquid Solenoid Valve (PS3), EVAP2 Defrost Hot Gas Solenoid Valve (PS4), Drain Heaters 3 and 4 (HT3, HT4) | 20 amps | 10 amps | |
| Fuse 9: (Spectrum Only) Evaporator Fan 3 | 15 amps | 10 amps | |
| Fuse 10: (Spectrum Only) Evaporator Fan 4 | 15 amps | 10 amps | |
| Fuse 11: Drain Heaters (H1 and H2) | 2 amps | 2 amps | |
| Fuse 17: Drain Heaters (H3 and H4) | 2 amps | 2 amps | |
| Fuse 20: Transformer AC Power Supply (located at compressor motor contactor in condenser section) | 4 amps | 4 amps | |
| Fuse 21: Battery Power Supply (located in 2 wire near battery) | 50 amps (Single Temp) | 60 amps (Multi-Temp) | |
| Fuse 31: Condenser Fan Motor 2 (CFM2) (located in CF2 wire near terminal strip in condenser section) | 16 amps | 10 amps | |
| V-800 and Spectrum | |||
| Fuse 6: Drain Heaters 1/2 | 2 amps | 2 amps | |
| Fuse 8: (Spectrum Only) EVAP2 Liquid Solenoid Valve (PS2), EVAP1 Liquid Solenoid Valve (PS3), EVAP2 Defrost Hot Gas Solenoid Valve (PS4), Drain Heaters 3 and 4 (HT3, HT4) | 20 amps | 10 amps | |
| Fuse 9: (Spectrum Only) Evaporator Fan 3 | 15 amps | 10 amps | |
| Fuse 10: (Spectrum Only) Evaporator Fan 4 | 15 amps | 10 amps* | |
| Fuse 11: Drain Heaters (H3 and H4) | 2 amps | 2 amps | |
| Fuse 15: TracKing | 5 amps | 5 amps | |
| Fuse 16: TracKing | 5 amps | 5 amps | |
| Fuse 17: TracKing | 5 amps | 5 amps | |
| Fuse 20: Transformer AC Power Supply (located at compressor motor contactor in condenser section) | 2 x 2 amps | 2 x 2 amps | |
| Fuse 21: Battery Power Supply (located in 2 wire near battery) | 2 x 30 amps | 2 x 30 amps | |
| Fuse 31: Condenser Fan Motor 2 (CFM2) (located in CF2 wire near terminal strip in condenser section) | 16 amps | 10 amps | |
|
Note * 15
A in Spectrum Versions with Double Evaporator Fan 4
|
|||
| Condenser Fan Motor (All except V-800) | |||
| Voltage | 13 Vdc | 26 Vdc | |
| Full Load Current | 10 Amps | 4.7 Amps | |
| Power Rating | 130 W | 122 W | |
| RPM with Full Load | 2,800 | 2,800 | |
| Condenser Fan Motor (V-800) | |||
| Voltage | 13 Vdc | 26 Vdc | |
| Full Load Current | 11 Amps | 9 Amps | |
| Power Rating | 145 W | 230 W | |
| RPM with Full Load | 2,670 | 2,900 | |
| Evaporator Fan Motors (Each) | |||
| Voltage | 13 Vdc | 26 Vdc | |
| Full Load Current | 7.5 Amps | 4 Amps | |
| Power Rating | 97.5 W | 104 W | |
| RPM with Full Load | 2,800 | 2,800 | |
| Coil for Hot Gas Solenoid (PS1, PS2, PS3, PS4) | |||
| Voltage | 12 Vdc | 24 Vdc | |
| Current | 2.3 amps | 1.3 amps | |
| Resistance | 5.2 ohms | 20 ohms | |
| Coil for Liquid Injection Solenoid (LIS) – MAX Only | |||
| Voltage | 12 Vdc | ||
| Current | 1.2 amps | ||
| Resistance | 10.0 ohms | ||
| Coil for Heat Pilot Solenoid (PS5) - Truck Engine Coolant Heat Option Only | |||
| Voltage | 12 Vdc | ||
| Current | 1.5 amps | ||
| Resistance | 8.0 ohms | ||
| Drain Line Heaters (Each) - MAX Only | |||
| Voltage | 12 Vdc | ||
| Current | 0.9 amps ± 5% at 68 F (20 C) | ||
| Resistance | 13.8 ohms ± 5% at 68 F (20 C) | ||
| Battery Relay (BATR) | |||
| Type | Single Pole Single Throw (SPST) | ||
| Contacts | Terminals 30 to 87 | Normally Open (NO) | |
| Coil Resistance | Terminals 85 to 86 | 90 ohms | |
| Electric Standby Power Relay (STDR) | |||
| Type | Single Pole Single Throw (SPST) | ||
| Contacts | Terminals 30 to 87 | Normally Open (NO) | |
| Coil Resistance | Terminals 85 to 86 | 90 ohms | |
| Start Key Relay (C1R) | |||
| Type | Single Pole Double Throw (SPDT) | ||
| Contacts |
Terminals 30 to 87 Terminals 30 to 87A |
Normally Open (NO) Normally Closwe (NC) |
|
| Coil Resistance | Terminals 85 to 86 | 90 ohms | |
| Capacitors | |||
| Starting Capacitor (CS) – all voltages | 250–300 μF | ||
| Running Capacitor (CR) | 40 μF | ||
| Compressor Motor Contactor (CMC) | |||
| Contacts | Normally Open | ||
| Coil Voltage | 12 Vdc | ||
| Coil Current | 0.25 amps | ||
| Coil Resistance | 48 ohms | ||
| Transformer | |||
| Power | 500 VA | ||
| Frequency | 50/60 Hz | ||
| Primary Inputs | 115-208-230 Vac | ||
| Secondary Nominal Voltage | 11.7 Vac (21.4 Amps) | ||
| Fuses | |||
| V-800/ V-1000 and Spectrum | 12 Vdc | 24 Vdc | |
| Fuse 1: Condenser Fan Motor (CFM1) | 15 amps | 10 amps | |
| Fuse 2: Condenser Fan Motor (CFM2) | 15 amps | 10 amps | |
| Fuse 3: Evaporator Fan 1 | 15 amps | 10 amps | |
| Fuse 4: Evaporator Fan 2 | 15 amps | 10 amps | |
| Fuse 5: PS1, PS7, CMC, LIV,PS5, RCV, CCL | 20 amps | 10 amps | |
| Fuse 6: Drain Heaters 1/2 | 2 amps | 2 amps | |
| Fuse 8: (Spectrum Only) EVAP2 Liquid Solenoid Valve (PS2), EVAP1 Liquid Solenoid Valve (PS3), EVAP2 Defrost Hot Gas Solenoid Valve (PS4), Drain Heaters 3 and 4 (HT3, HT4) | 20 amps | 10 amps | |
| Fuse 9: (Spectrum Only) Evaporator Fan 3 | 15 amps | 10 amps | |
| Fuse 10: (Spectrum Only) Evaporator Fan 4 | 15 amps | 10 amps* | |
| Fuse 11: Drain Heaters (H3 and H4) | 2 amps | 2 amps | |
| Fuse 14: Ignition | 5 amps | 5 amps | |
| Fuse 17: TracKing | 5 amps | 5 amps | |
| Fuse 20: Transformer AC Power Supply |
5 amps (time delay fuse) |
5 amps (time delay fuse) |
|
| Fuse 21: Battery Power Supply | 100 amps | 60 amps | |
| Fuse 41: Evaporator Fan 5 | 15 amps | 10 amps | |
| Fuse 42: Evaporator Fan 6 | 15 amps | 10 amps | |
| Condenser Fan Motor | |||
| Voltage | 13 Vdc | 26 Vdc | |
| Full Load Current | 11 amps | 4.7 amps | |
| Power Rating | 145 W | 288 W | |
| RPM with Full Load | 2,570 | 3,400 | |
| Control voltage range | 1-10 Vdc | 6.5-10 Vdc | |
| Evaporator Fan Motors (Each) | |||
| Voltage | 13 Vdc | 26 Vdc | |
| Full Load Current | 7.5 amps | 4 amps | |
| Power Rating | 97.5 W | 104 W | |
| RPM with Full Load | 2,800 | 2,800 | |
| AC Electrical Power Supply Motor | |||
| Voltage/Phase/Frequency | 230/1/50, 230/3/60, 400/3/50 | ||
| Output Power | 0.75 kW | ||
| Nominal Current Drawn | 5.2 amps | ||
| OL Relay Adjustment |
10 / 20 Units - 5.2 amps 30 / 50 Units - 10.5 amps |
||
| DC Electrical Power Supply Motor | |||
| Voltage | 12 Vdc | 24 Vdc | |
| Output Power | 600 W | 600 W | |
| Nominal Current Drawn | 65 amps | 30 amps | |
| Coil for Hot Gas Solenoid (PS1, PS2, PS3, PS4) | |||
| Voltage | 12 Vdc | 24 Vdc | |
| Current | 14 W | 14 W | |
| Coil for Liquid Injection Solenoid (LIS) – MAX Only | |||
| Voltage | 12 Vdc | 24 Vdc | |
| Current | 14 W | 14 W | |
| Coil for Heat Pilot Solenoid (PS5) - Truck Engine Coolant Heat Option Only | |||
| Voltage | 12 Vdc | 24 Vdc | |
| Current | 21 amps | 21 W | |
| Drain Line Heaters (Each) - MAX Only | |||
| Voltage | 12 Vdc | 24 Vdc | |
| Resistance | 2.095 ohm | 7.5 ohm | |
| Battery Relay (BATR) | |||
| Type | Single Pole Single Throw (SPST) | ||
| Contacts | Terminals 30 to 87 | Normally Open (NO) | |
| Coil Resistance | Terminals 85 to 86 | 90 ohms | |
| Electric Standby Power Relay (STDR) | |||
| Type | Single Pole Single Throw (SPST) | ||
| Contacts | Terminals 30 to 87 Terminals 30 to 87A |
Normally Open (NO) Normally Close (NC) |
|
| Coil Resistance | Terminals 85 to 86 | 90 ohms | |
| Compressor Motor Contactor (CMC) | |||
| Contacts | Normally Open | Normally Open | |
| Coil Voltage | 12 Vdc | 24 Vdc | |
| Coil Current | 0.25 amps | 5.4 Watt | |
| Transformer | |||
| Power | 1100 VA | ||
| Frequency | 50/60 Hz | ||
| Primary Inputs | 230-400 Vac | ||
| Secondary Nominal Voltage | 2 windings: 11.7 Vac (47 amps) 11.7 Vac (47 amps) |
||
AC Electric Compressor Motors and Overload Relays
| Voltage/Phase/Frequency | Horsepower | Kilowatts | RPM | Full Load (amps) | Overload Relay Setting (amps) |
|---|---|---|---|---|---|
| V-100/V-200s | |||||
| 230/1/50 | 2.0 | 1.5 | 1750 | 5.4 | 5.5 |
| V-200/V-300 | |||||
| 230/1/50 | 2.0 | 1.5 | 1750 | 8.6 | 8.6 |
| 230/1/60 | 2.0 | 1.5 | 1750 | 9 | 9 |
| 230/3/60 | 2.4 | 1.8 | 1750 | 6.9 | 6.9 |
| 400/3/50 | 2.4 | 1.8 | 1750 | 4 | 4 |
| 400/3/60 | 2.4 | 1.8 | 1750 | 4 | 4 |
| V-500/V-600 | |||||
| 115/1/60 | 1.5 | 1.1 | 1710 | 14 | 14 |
| 208/1/60 | 2.0 | 1.5 | 1740 | 9.5 | 9.5 |
| 230/1/60 | 2.0 | 1.5 | 1750 | 9 | 9 |
| 208/3/60 | 2.4 | 1.8 | 1730 | 7.2 | 7.2 |
| 230/3/60 | 2.4 | 1.8 | 1750 | 6.9 | 7 |
| V-800 (ES600+2xES150) | |||||
| 230/3/50 | 2.4 | 1.8 | 1750 | 66.6/9.6 amps | 9.6 |
| 230/3/60 | 2.4 | 1.8 | 1750 | 19.9/11.5 amps | 11.5 |
| V-800 | |||||
| 230/3/50 | 3 | 2.3 | 1450 | 57/16.6 amps | 18 |
| 400/3/50 | 3 | 2.3 | 1450 | 32.9/9.6 amps | 14 |
| 230/3/60 | 3 | 2.3 | 1740 | 68.4/19.9 amps | 18 |
| 400/3/60 | 3 | 2.3 | 1740 | 39.5/11.5 amps | 14 |
| V-1000 | |||||
| 230/3/50 | 5 | 3.7 | 1450 | 22/109 amps | 24 |
| 400/3/50 | 5 | 3.7 | 1450 | 12.7/63.1 amps | 16 |
| 230/3/60 | 5 | 3.7 | 1740 | 26.5/121 amps | 24 |
| 400/3/60 | 5 | 3.7 | 1740 | 15.3/70.1 amps | 16 |
| Fuses | |||
| C-150, C-250, C-350, C-450, C-550, C-650, C-750 | 12 Vdc | 24 Vdc | |
| Fuse 1 | 3 amps | 3 amps | |
| Fuse 2 | 15 amps | 7.5 amps | |
| Fuse 3 | 15 amps | 7.5 amps | |
| Fuse 4 | 15 amps | 7.5 amps | |
| Fuse 5 | 15 amps | 7.5 amps | |
| Fuse 14 | 5 amps | 5 amps | |
| Fuse 21 | 40 amps | 30 amps | |
| Fuse 30 | 2 amps | 2 amps | |
| Condenser Fan Motor | |||
| Voltage | 13 Vdc | 26 Vdc | |
| Full Load Current | 9.2 amps | 4.1 amps | |
| Power Rating | 100 W | 100 W | |
| RPM with Full Load | 2,800 | 2,800 | |
| Control voltage range | ?? Vdc | ?? Vdc | |
| Evaporator Fan Motors (Each) | |||
| Voltage | 13 Vdc | 26 Vdc | |
| Full Load Current | 6.2 amps | 3.7 amps | |
| Power Rating | 100 W | 100 W | |
| RPM with Full Load | 2,800 | 2,800 | |
| Coil for Hot Gas Solenoid (PS1, PS2, PS3, PS4) | |||
| Voltage | 12 Vdc | 24 Vdc | |
| Current | 14 W | 14 W | |
| Coil for Liquid Injection Solenoid (LIS) – MAX Only | |||
| Voltage | 12 Vdc | 24 Vdc | |
| Current | 14 W | 14 W | |
| Drain Line Heaters (Each) - MAX Only | |||
| Voltage | 12 Vdc | 24 Vdc | |
| Resistance | 2.095 ohm | 7.5 ohm | |